The diesel generator controller system consists of magneto, low-voltage cable, incineration coil, high-voltage cable The structure and device of magneto are composed of spark plug and incineration switch. The magneto system is contactless. In the process of working, there is no spark to meet the explosion-proof requirements. The output electric pressure is 160-180v DC). From the direction of a, the rotation direction of the driving wheel is counterclockwise. The driving wheel of the generator control module rolls for three turns to complete an operating cycle of the engine, that is, the speed ratio between it and the crankshaft is 1.5:1 supplied by the diesel generator set The low-voltage electric energy is stored in the capacitor 7. When the rotating punctual distribution arm 6 driven by the reduction gear passes through the sensor coil, it will excite the SCR electronic switch in order to transfer the energy of the electric container to the incineration coil. The resulting high-voltage electricity will cause the spark plug to jump. Before starting the magneto of the controller device, the flywheel must be rolled to make the top cylinder 32 crankshaft angle magnetoelectricity before the top dead center of the incineration advance angle azimuth An investigation hole is set at the tail end of the machine to see the red line symbol rotating with the shaft and the red line symbol under the white CCW word on the shell, and then roll the drive disk of the magneto to make the two red line symbols into a straight line. The generator unit controller can install the magneto and tighten the two screws connected with the transmission device. At this time, the incineration advance angle is an approximate value and an accurate adjustment method of the incineration advance angle

松開磁電機與傳動裝置的兩個螺釘發電機控制屏磁電機可沿傳動軸線滾動發電機電子調速器磁電機由中間方位向自由端方向滾動至大的方位時焚燒提早角滯后約10曲軸轉角左右反之向輸出端滾動至大方位時柴油發電機組控制器焚燒提早角提早約10曲軸轉角左右柴油發電機工作時銜接磁電機的2個螺釘要確保擰緊

Loosen the two screws between the magneto and the transmission device. The magneto on the generator control panel can roll along the transmission axis. When the magneto of the generator electronic governor rolls from the middle direction to the free end to the maximum direction, the incineration advance angle lags about 10 crankshaft angle. On the contrary, when rolling to the output end to the maximum direction, the incineration advance angle of the diesel generator set controller is about 10 crankshaft angle Ensure that the two screws connecting the magneto are tightened when the oil generator is working

磁電機裝上低壓電纜插頭引出14根低壓電線每根電線均標示不同符號依照發火次序與每個氣缸的焚燒線圈+極聯接符號N的電線與每排缸的焚燒線圈一極串聯而且兩排缸并聯符號G的電線與焚燒開關銜接其接線方法為發電機配件斷路時發動機工作接地時則發動機停車

The magneto is equipped with a low-voltage cable plug to lead out 14 low-voltage wires. Each wire is marked with different symbols. According to the firing order, it is connected with the incineration coil + pole of each cylinder. The wire of symbol n is connected in series with one pole of the incineration coil of each row of cylinders, and the wire of symbol g in parallel of the two rows of cylinders is connected with the incineration switch. The wiring method is that the engine stops when the generator accessories are open circuit and the engine is grounded

低壓電纜經過低壓電纜把磁電機輸出的電能傳遞到焚燒線圈不同類型的磁電機要配相應標準的低壓電纜由插頭引出的一股電纜內每根電線均標示不同的符號根據發動機的發火次序把每根電線銜接到對應氣缸的焚燒線圈的正極、負極焚燒開關及接地等

The low-voltage cable transmits the electric energy output by the magneto to the incineration coil through the low-voltage cable. Different types of magnetos shall be equipped with corresponding standard low-voltage cables. Each wire in a cable led out from the plug shall be marked with different symbols. Each wire shall be connected to the positive and negative incineration switches and grounding of the incineration coil of the corresponding cylinder according to the ignition sequence of the engine

焚燒線圈焚燒線圈將磁電機輸出的低壓電轉變?yōu)楦邏弘姲l(fā)電機調速器不同類型的磁電機應配相應標準的焚燒線圈本機所用焚燒線圈高輸出電壓為40000VDC)當輸出電壓為10000V時火花塞跳火持續時間為550微秒正、負南北極與電線聯接時要把螺帽擰緊

Incineration coil incineration coil converts the low-voltage power output by the magneto into high-voltage electric generator governor. Different types of magneto shall be equipped with corresponding standard incineration coil. The maximum output voltage of the incineration coil used by this machine is 40000 VDC). When the output voltage is 10000 V, the duration of spark plug ignition is 550 microseconds. When the positive and negative south north poles are connected with the wire, tighten the nut

火花塞火花塞螺紋為M18×1.5mm裝入缸頭時其扭緊力矩為42-52N.m擰緊后應確保火花塞底部的螺紋端面與缸蓋底面平齊火花塞空隙為0. 6mm當空隙值增大到0.89mm時火花塞將呈現失火現象使發動機工作不穩甚至停車發電機控制器要求按不同的運用條件定時查看火花塞清除火花塞及其螺紋處呈現的積炭

Spark plug the spark plug thread is M18 × When 1.5mm is installed into the cylinder head, the tightening torque is 42-52n. M. after tightening, ensure that the threaded end face at the bottom of the spark plug is flush with the bottom of the cylinder head. The gap of the spark plug is 0.6mm. When the gap value increases to 0.89mm, the spark plug will show misfire, making the engine unstable and even stopping the generator. The controller requires to regularly check the spark plug according to different application conditions and remove the carbon deposits at the spark plug and its threads